24V ∞Seeds - 1020ct reel

∞Power , ∞Colors, ∞Runs.

The ∞Technology is the result of countless hours of researches, hard work and our personal on field experience. We listened to a lot of customers feedbacks, and created ∞Lineup for you.

In traditional seeds, each pixel has to lower the supplied 12v to 5v internally for the Led Diodes and the WS2811 IC.

This is achieved using electrical components that are wasting the extra voltage through heat and can lead to strange behaviors, like white turning in pink, or other issues when voltage drop occurs.

∞Power

∞Seeds are using higher voltages combined with a new style of individually addressable series-connected LEDs. Our LEDs are splitting the supplied 24V on 6 LEDs, 
Achieving an ultra low power consumption of only 0.04W/seed at 100% brightness, plus a regulator free, low-heat design.

Stop worrying for thin seed wires overheating, due to the high current flow.
With 24V you can carry more power in your run, while still keeping the same amount of amps as before. The wire and the LEDs operates at a lower temperature, resulting in elongated lifetime of the strand over time.
And since they have a constant consumption at whatever color or brightness level, it’s easy for you to tell how much power they will draw at max. No more popping fuses with accidental white or too much high brightness.

∞Colors 

Most of the Seed pixel users runs their seeds at 50%  brightness. At this brightness % they can only reproduce 2.1M colors. 

∞Seeds at 100% brightness will reach the same luminous output as traditional 12v seeds set to 50%.
Allowing ∞Seeds to display 8x more colors, with a full 16.8M colors spectrum to play with. 
Colors are more vivid, shades more natural. We highly recommend to run them at 100% brightness.

And If ∞Seeds at 100% are still too bright for you, you can still lower the brightness or combine them with the xLights gamma correction, for getting the best in class colors on your show.

∞Customization 

∞Seeds are available in three epoxy finishes, 2/4/6 inch spacing and Black, Green or Clear Wire.

- Milky Epoxy, offers the best 360° effect, with smooth colors and a soft overall effect. 

- Translucent Epoxy, is halfway between milky and clear, still retaining a 360° effect with a more brighter front and more vivid colors.

- Clear Epoxy, offers the brightest and shinier look, with sharp colors. more suitable for front facing installations, like props or matrices, or where you want the traditional shiny look. 

∞Runs

With ∞Seeds you can easily maximize the number of LEDs/port on your controller without having to deal with Power injection/power balancing wires, if you don’t want to. 

A single strand of 24v ∞Seeds with power only from the beginning of your run can reach:

2” spacing
~ 480 LEDs - 78 ft - 18.65W 

4” spacing:
~ 330 LEDs - 108 ft - 13.15W

6” spacing:
~ 258 LEDs - 127 ft - 10.55W

Those numbers can be doubled by adding an end balance point, tripled by adding a 2/3 injection point or quadrupled by adding a front + middle + end injection point. 

In Example for 6” runs:

• 258 LEDs - Power at led 1 (start) 

• 516 LEDs  - Power at led 1 (start), power at led 516 (end) 

• 774 LEDs - power at led 1 (start), power at led 516 (2/3) 

• 1032 LEDs - Power at led 1 (start), power at led 516 (middle) and power at led 1032 (end) 

(Actual results may vary based on your setup.) 

24V ∞Seeds:

• DC 24V (20.4V min - 25.2V Max recommended, up to 45V tested.)
• 6 LEDs/section.
• Low power consumption - 0.04W/Led 
• Standard WS2811 Protocol
• GRB color order.
• Longest runs ever on Seed pixels.
• Individually addressable series design. 
• 2” - 4” - 6” spacing options.
• Black, Clear or green wire.
• Upgraded thicker wires design. (0.2 sq. mm)
• Low heat on wires.
• Improved colors reproduction.

6 Month Warranty